Detector PCB for 4500 MkIII

Calibration Motor & Gearbox

AMETEK Land

AMETEK Land item no. 804368 Motor for 4500 MkIII automatic calibration unit

Main PCB for 4500 MkIII

AMETEK Land

AMETEK Land item no. 804320 Main circuit board with microprocessor. Configuration required - be sure to follow fitting instructions.

Flood LED PCB for 4500 MkIII

AMETEK Land

AMETEK Land item no. 804321 Flood LED including mount and connector.

Recommended Spare Parts Kit - 4650-PM

AMETEK Land

AMETEK Land item no. 810621

AFU Enclosure Lid and Hinge (spare)

AMETEK Land

AMETEK Land item no. 812672 Replacement door for 4500 MkIII AFU-APS-I/O

Ethernet AFU PCB (Tested) - 4500 MkIII

AMETEK Land

AMETEK Land item no. 804651 Ethernet module for 4500 MkIII AFU

9100 Spare Source Heater

AMETEK Land

AMETEK Land item no.812105 Replacement for obsolete infrared source 703.579. Includes an upgrade to firmware V1.1.

Spare Actuator Digital Cable

AMETEK Land

AMETEK Land item no. 812033 M12 Ethernet M-F D Coded Cable Digital Power Cable 0.5M for SPOT Actuator - A specific length cable with an M12PoE connector, the other end a RJ45 fitting for a network...

M16 8 Way to M16 12 Way Analogue Cable 0.3m

AMETEK Land

AMETEK Land item no. 808084 The M16 8 way to M16 12 way connector allows for replacement of non System 4 instruments.

SPOT to System 4 Adaptor Kit

AMETEK Land

AMETEK Land item no. 808018 The System 4 to SPOT Adapter Kit allows you to install an AMETEK Land SPOT Pyrometer in an S4-J. This means that you can replace an existing System 4 Pyrometer with an...

Small Pan & Tilt Bracket

AMETEK Land

AMETEK Land item no. 806761 This dual axis mounting bracket can be used with the water cooled mounting where the mounting front flange is inappropriate.

Analog Connection PCB Kit

AMETEK Land

AMETEK Land item no. 807942 PCB connection board for use with the above cable selection. The customer is free to wire to the 24V power supply of their choice.

IP 68 Plug (For S4 Cable Assembly)

AMETEK Land

AMETEK Land item no. 212.372

S4 Connector & Cable 35m 6 Cores

AMETEK Land

AMETEK Land item no. 800589 For System 4 Thermometers fully assembled with ODU-Plug.

System 4 Connector & Cable 10 metre

AMETEK Land

AMETEK Land item no. 990.615 Fully assembled with ODU-Plug, Cable length: 10 Metres.

Blower Air Hose Clip

AMETEK Land

AMETEK Land item no. 150.139 Worm drive hose clip.

I/O Processor 1 - IN(4D/2A) OUT(4D/4A)

AMETEK Land

AMETEK Land item no. 812835 *** new part number 812835 *** Beckhoff I/O Processor 1 Inputs: 4 digital, 2 analogue. Outputs: 4 digital, 4 analogue Provides analog and digital I/Os for a maximum of 8...

PoE Power Supply for Service Panel

AMETEK Land

AMETEK Land item no. 807105 DIN rail mounting, Supply voltage: 48 V DC, Dimensions: 48.6 x 140 x 95 mm (W x H x D) max. Ambient temperature: LSP-HD 80 ° C, Connection: RJ45 Power over Ethernet...

M12 Phoenix Connector (4 pin)

AMETEK Land

AMETEK Land item no. 805199

4 way M12 to RJ45 Cable (0.5m)

AMETEK Land

AMETEK Land item no. 805023 Connection 1: Ethernet M12 connector, Connection 2: RJ 45 Plug, Connection 1: Ethernet M12 connector, Connection 2: RJ 45 Plug

FGA 0.5 m Probe

AMETEK Land

AMETEK Land item no. 702.424 Probe comprises a 19mm stainless steel tube with a 25·m sintered tip. Mounting flange is 3/4inch ANSI 150lb (flat-face, 98 od., 27.5 id., four 13.0 holes on 70 pcd...

Purge Pump PCB (FGA 9xx SERIES)

AMETEK Land

AMETEK Land item no. 702.821 Purge pump for CO sensor overload protection.

2 Year Spares Kit (FGA900 series)

AMETEK Land

AMETEK Land item no. 703.646 6 pieces gas filter, 317.476 3 pieces Twin Autoprene Tube Assembly, 801402 6 pieces Replacement pump head, 317.553 2 pieces Replacement Viton Diaphragm, 317.552

FGA9xx CO Sensor Unit

AMETEK Land

AMETEK Land item no. 703.016 FGA9xx CO Sensor Unit Spent sensors contain toxic and acidic elements hazardous to the environment, and should be disposed of in accordance with prevailing hazardous...

Additional Calibration Points

AMETEK Land

AMETEK Land item no. CAL PTS Add additional calibration test points to the Standard 3 point ISO Certificate (optional item). Test points must be specified by customer. PLEASE ENTER THE TEMPERATURE...